PT600

PT600

Insulating Plaster

  • PRODUCT INFO

    an insulating plaster for blockwork and fibre-cement sheet.

  • TECHNICAL INFORMATION

    Insulating Render HEIDELBERGER PT600
    PT 600 is a factory mixed dry plaster following European standard DIN 18550 and DIN 18555 and has been formulated for use as an insulating plaster.
    A machine plaster, PT 600 can be applied directly onto all masonry substrates including bre- cement sheet.
    Preparation
    The substrate must be of a sound nature, free from dust and loose particles, form release oils and other contaminants which could affect adhesion and bonding strengths of subsequent coatings.
    Substrates with voids, defects and uneven surfaces do not require special preparation.
    In the case of smooth concrete a key (PT 300) must be applied prior to the application of PT 600. Contact Putz-technik for specific application details.
    Application
    With excellent adhesion and having a favourable compression/flexural strength ratio, PT 600 is suitable for commercial plastering machines or manual application (drill or machine mixed). PT 600 can be used as a basecoat on rough concrete, concrete block or bre- cement sheet at a thickness of 10mm to 100mm.
    In areas of known or potential stress such as door and window lintels, dissimilar substrates, panel deflection due to wind loading etc, we recommend the use of Fibreglass Mesh breglass reinforcing mesh embedded wet-in-wet in the plaster or in a separate meshcoat (PT 320). Ensure that the breglass mesh is trowelled in such a way that it remains towards the exterior surface of the plaster and that it is overlapped at least 100mm where it is joined.
    During setting the applied areas may be screeded and cut. Once the required straightness and surface has been achieved, and following sufficient drying time, further coats of plaster can be applied. It is recommended that ‘h’ profile straight-edges be used with this product for best results.
    Page | 33
    Coverage
    Depending on the substrate 1 bag of PT 600 yields approximately 1.4 square metres at 25mm thickness.
    Important
    Do not under any circumstances add foreign substances other than clean water to premixed mineral plasters.
    PT 600 should not be applied to wet or green cementitious substrates before a reasonable curing/drying period.
    Allow a reasonable drying time prior to applying further coats of plaster. If necessary, contact Putz-technik for further information on drying times.
    Technical
    PT 600 is manufactured using selected grades of lime, cement, perlite and mineral additives. Particle size range is 0—2.0mm.
    PT 600 has a high water vapour permeability (breathing activity). Where a re resistance rating is required please contact Putz-technik.
    Water demand
    340
    Water retention % 91.1 Flexural strength N/mm²
    1.98
    Compressive strength N/mm²
    4.7
    Bond strength N/mm²
    0.45
    INSULATION DATA for Gib lined or internally (gypsum) plastered 200mm concrete block wall (combined R - Value = 0.368) + varying thicknesses of PT 600
    Thickness PT 600
    R – Value
    10mm
    0.48
    20mm
    0.59
    30mm
    0.70
    40mm
    0.81
    50mm
    0.92
    60mm
    1.04
    70mm
    1.15
    80mm
    1.26
    90mm
    1.37
    100mm
    1.49
    Storage
    PT 600 is packaged in paper bags.
    PT 600 can be stored in a dry place for up to 6 months.
    Page | 34
    Quality Control
    PT 600 is quality controlled at point of manufacture and tested by independent laboratories.
    Service
    At the forefront of plastering technology, Putz-technik offers its assistance and experience in the selection and use of our products and machines.
    Demonstrations are available on request

  • SHIPPING INFO

    Avalible instore or shipping can be arranged

$43.70Price
Size

099216531

  • Facebook
  • Twitter
  • LinkedIn

©2020 by Putz-Technik. Proudly created with Wix.com